Product News

Loop-Powered Pepperl+Fuchs KFD0-CS-Ex2.50P Two-Channel 4-20 mA Repeater for Intrinsically Safe Transmitter and Current-Loop Isolation

News November 17, 2026

Two Independent 4-20 mA Loops Without an Auxiliary Supply: KFD0-CS-Ex2.50P Engineering Overview

Pepperl+Fuchs KFD0-CS-Ex2.50P is a two-channel isolated barrier designed for analogue current-loop applications in which hazardous-area field signals must be transferred to the safe side with galvanic isolation. Its loop-powered architecture is especially useful when a cabinet design does not provide a separate supply connection for the isolator. Each channel handles a 4-20 mA signal independently, allowing one compact module to serve two measurement loops while preserving electrical separation.

The complete model number matters. KFD0-CS-Ex2.50P identifies a specific two-channel configuration within the Pepperl+Fuchs K-System range; nearby KFD0-CS variants can differ in channel count, signal arrangement, or output characteristics. For replacement work, the suffix should be checked against the installed label, loop drawing, and hazardous-area documentation before an order is confirmed.

What Makes the Loop-Powered Design Useful

KFD0-CS-Ex2.50P draws its operating energy from the connected current loop rather than from a separate auxiliary-power terminal. This can simplify wiring in retrofit panels, reduce the number of cabinet supply connections, and support projects where the original control-panel layout must remain largely unchanged. The module can be applied as a current repeater or as a transmitter power supply for compatible two-wire field transmitters.

Because the two channels are independent, maintenance teams can review and troubleshoot one loop without treating the module as a single combined signal path. The manufacturer specifies 4-20 mA input and output operation, 0.1% accuracy, reverse-polarity protection, and a 5-35 V DC loop-powered operating range. KFD0-CS-Ex2.50P is also listed for SIL 2 applications with Systematic Capability SC 3, subject to the complete safety-loop design and the applicable documentation.

How the Signal Path Is Arranged

In a typical installation, the KFD0-CS-Ex2.50P signal path can be reviewed in four practical steps:

  • A hazardous-area transmitter produces a 4-20 mA measurement signal.
  • The corresponding KFD0-CS-Ex2.50P channel receives the field-loop current through the intrinsically safe side.
  • Galvanic isolation separates the field circuit from the safe-area control circuit.
  • The safe-side current output is connected to a compatible DCS, PLC, recorder, or analogue input card.

This arrangement helps limit unwanted interaction between hazardous- and safe-area wiring while maintaining the analogue value required by the control system. It is commonly considered for pressure, flow, level, temperature, and other process measurements where a two-wire transmitter or 4-20 mA source must communicate with safe-area equipment.

The Voltage Budget Is the Key Selection Check

A loop-powered isolator introduces a voltage requirement into the circuit. Before selecting KFD0-CS-Ex2.50P, the engineer should calculate the voltage available after accounting for the receiving-card input resistance, cable resistance, field-transmitter demand, barriers, terminals, and the highest expected loop current. A module may match the model number and signal type yet still be unsuitable if the remaining voltage cannot operate the transmitter across the full measurement range.

For hazardous-area service, entity parameters, gas group, zone or division, temperature class, field-device certification, and cable capacitance and inductance must also be checked as a complete system. Product-family similarity is not a substitute for reviewing the certificate and installation conditions that apply to the exact KFD0-CS-Ex2.50P configuration.

Replacement and Procurement Notes

For a faster and more accurate quotation, record the following information before requesting KFD0-CS-Ex2.50P:

  • Full model number and a clear photograph of the front and side labels
  • Required quantity, product condition, destination country, and delivery deadline
  • Field-device type and whether the loop is transmitter-powered or independently powered
  • DCS or PLC analogue-input resistance and available loop voltage
  • Hazardous-area classification, safety parameters, and any SIL requirement

A clear loop drawing is particularly helpful when KFD0-CS-Ex2.50P is being sourced for an urgent shutdown replacement. It allows the channel arrangement, terminal use, voltage budget, and receiving equipment to be reviewed before shipment, reducing the chance of selecting a visually similar but electrically different K-System module.

Other hot sales models for your reference.

KFD0-CS-Ex1.50P, KFD0-CS-Ex1.51P, KFD0-CS-Ex2.51P, KFD0-CS-Ex1.52, KFD0-CS-Ex2.52, KFD0-CS-Ex1.53, KFD0-CS-Ex2.53, KFD0-CS-Ex1.54, KFD0-CS-Ex2.54, KFD0-SCS-Ex1.55, KCD2-RR-Ex1, KFD2-VR-Ex1.18, KFD2-VR-Ex1.19, KFD2-VR2-Ex1.50M, and KFD2-VR4-Ex1.26.

Sunup-MTL supports model confirmation, availability checks, quotation, export documentation, and international delivery for Pepperl+Fuchs isolated barriers and industrial automation spare parts. Please send the complete model number and project requirements so the correct item can be reviewed before order arrangement.